How to Replace a Whirlpool Refrigerator Water Filter
How to replace a whirlpool refrigerator water filter. Water filters need to be changed every six months to ensure optimal performance.
If a filter is left unchanged for longer than six months, then the water being pulled from the refrigerator will start to taste funny and look murky, the ice could smell, and you may notice black specks in the water.
Additionally, if a filter is not replaced, it can affect the water flow, causing water to slowly trickle out of your fridge and smaller ice blocks to be produced.
Replacing your refrigerator’s water filter is simple if you know the best time to do it. Keeping the water clean is essential because it helps everything work better: ice-makers, the condenser, and the evaporator.
The process usually doesn’t require any. A replacement filter that matches your original will ensure the installation job goes smoothly and without issues.
Even though using our guide on replacing a water filter for your Whirlpool refrigerator can help.
It is helpful to look at a specific model number since water filters often follow certain patterns based on their type, even if they are Whirlpool part numbers.
How to Replace a Whirlpool Refrigerator Water Filter
Here’s how you can change the Whirlpool refrigerator water filter in 5 simple steps:
1. Locating your Whirlpool refrigerator’s water filter can be a bit of a puzzle, but it doesn’t have to be!
Depending on your model and installation, you’ll need to get it from either the back right corner or underneath the ice dispenser (in some cases in the freezer itself).
Check your model’s manual to see which placement applies to you.
If this isn’t an option, don’t worry – we can help! Contact our Sales department by way of chat or phone, and we’ll make sure we get you on your way with a fresh supply of delicious clean drinking water.
2. When changing your water filter, be prepared for some spillage. Be sure to put a towel down before removing the old filter. Suppose you want to access the new water filter from inside the refrigerator.
In that case, it may be a brilliant idea to remove any food or drinks you have stored on the racks near the filtered water tank not accidentally tip them over because change takes time.
If your refrigerator has an ice maker, you’ll have to shut it off before you change its water filter. Don’t worry – the water supply should turn off automatically when you remove the filter anyways.
On some older models, the water might spill out if the ice maker makes ice while you’re changing the filter.
But for most refrigerators, this step is not required as their water supply will shut off automatically when you replace their old filers.
Changing your refrigerator’s water filter will not require that you access any electrical components of your appliance.
3. If the water filter is located in the grille of your refrigerator, you should be able to press firmly on the button located to the left of the filter.
Turning it a quarter turn counterclockwise should release it. If you need help, check your manual for instructions or contact customer support.
If your refrigerator model does not have a button to push or turn and doesn’t mention that in its user manual.
Don’t hesitate to get in touch with customer support, which will help you figure out what you can do to remove and replace the old filter with a new one.
Once your product is released, you should remove the old water filter from the refrigerator. Press more firmly on the release button, as sometimes it can stick and apply more pressure when turning the filter.
4. Replacing your water filter should be relatively easy. Pop the old filter out of its slot, slide the new one in, and lock it into place by turning it clockwise or pushing it straight in until you hear a click and it locks into place.
Ensure that the new filter is facing in the same direction as the old one before proceeding. That way, when you turn on the faucet, water will flow through both filters and prevent any potential issues.
If your filter comes with installation instructions, make sure to follow those to ensure that everything is installed correctly.
5. Run one gallon of fresh water through the filtration system after installation and then flush with four more gallons of fresh water.
Change the sediment filter in your refrigerator every six months or according to the manufacturer’s specifications – as indicated on the model’s filter, change the light, if applicable.
After how much time should I replace Whirlpool Water Filter?
Fortunately, there are a variety of different filter replacement options for refrigerators. Most standard filters last 6 to 12 months, and most feature an indicator that lets you know when it’s time to change your filter again.
However, one should also be aware of these other factors: whether the filter is used constantly.
How fast the filtration flow rate is, and how often this particular fridge is opened up, affect how quickly one may need to change the filter again.
Conclusion
We hope our guide has helped you replace the whirlpool fridge water filter. Don’t hesitate to discuss any issue in the comment section.
Thank you for your time. Have a nice day!
Related Post
